• How to Vent an Over-the-Range Microwave to the Outside | Today's Homeowner;
• cannot connect to matchmaking servers cs go;
• write a good online dating email;
• ?
• Installing an Over the Range Microwave?
• spartace couple dating;

You also need a cabinet the microwave hangs from. The cabinet not only provides support but it also contains the wiring for the microwave and may contain part of the venting.

You'll need to spend about two hours to hang the microwave from the wall and cabinet; longer if venting and wiring is required. Before you begin, move the range if it's in the way, and install a microwave cabinet. Install the vent and cover it with drywall. Cut through the drywall with a drywall saw to access the vent. Over-the-range microwaves hang from a cabinet. Install an outlet for the microwave inside the cabinet. The microwave can vent through the wall or the roof. On some microwaves you'll adjust the vent to channel the air in the right direction.

On others, including this one, you'll position the fan to channel the air. Many microwaves come with a template for mounting. Tape the template to the wall, drill where shown, then remove the template. If there is no template, follow the manufacturer's directions to lay out the mounting holes.

Attach the mounting plate to the wall.

Session Timeout

The exact method depends on where the studs fall and on the design of the plate. You need to attach to at least one stud but can probably use toggle bolts elsewhere. Follow the manufacturer's directions. Make sure the door is latched and have someone help you hang the microwave on the mounting plate. In this manner the back of the microwave is sealed against the wall except for the ducting, and air must go up the duct instead of around small cracks behind the installed microwave and back into the room. This can be seen in the photo above that also shows the bolts passing through the cabinet bottom.

It is the gray area around the duct. The actual installation of the microwave is quite simple - the bottom rear of the microwave is set onto the small hooks on the rear bracket screwed to the wall, the plug and cord fed up inside the cabinet, and the unit tipped up into place. The long screws need to be placed through the holes in the bottom of the cabinet and screwed into the microwave and the cord plugged in. My unit had three screws into the top of the microwave, with a notation that the center one is not to be tightened too much. In my case the grease screens needed to be installed into the bottom of the microwave and the glass turntable set into place.

The clear plastic film over the keypad needed to be removed, and voila! Most of the tools I used are common around the house, although I did use an impact driver for driving the wood screws.

1. speed dating palm beach gardens;
2. zeus dating commercial;
3. VIDEO: How to Install an Over the Range Microwave - Whirlpool Home Appliances;
4. Session Timed Out?
5. How to do it?
6. How to Install an Over-the-Range Microwave?
7. How to Install an Over The Range Microwave: 15 Steps;

A cordless drill will work nearly as well, and even a screwdriver would do the job with a good deal of effort the screws provided are quite large. Probably the biggest obstacle for most homeowners will be a lack of confidence, but you can learn to do most home repairs yourself - all it takes is a little time and a few of the right tools. My own experience in installing this particular over the range microwave would tend to indicate that they can be installed in virtually any home.

How to Install an Over-the-Range Microwave | Dengarden

At absolutele worst I would expect a new power line to have to be pulled from the circuit panel or nearby plug, and new ducting installed if there is none and the owner insists on an outside duct. On a scale of 1 - 10, this task rates about a 3. My total time, including mounting the new plug, cleaning up afterward and taking photos was about 2 hours. The microwave should be no less than 13" above the range.

In addition, it should be no more than 54" above the floor - any less and it can be difficult for shorter people to use. What if the existing vent to the outside and the new microwaves vent do not match up?

There is an inch between the top of the microwave and the bottom of the cupboard. Does the microwave need its own circuit?

How to Vent an Over-the-Range Microwave to the Outside

Our existing hood fan does not vent to the outside. So I need ductwork to the outside for a proper install? Only if you want to vent the range fumes and steam outside. Most if not all microwaves come with the ability to either vent outside through a duct or to filter it and blow back inside. Considering how much can be put in a cabinet, and how much is typically put into cabinets high over a range, there should never be a problem. Plus, of course, the wall is carrying a good deal of the weight.

Tipping one into place and screwing it to the cabinet takes some effort, but a lot of the reason is bulkiness and awkwardness. The actual weight of the cabinet is not great. As far as I know, no. While it would be possible to design such a system it would certainly require additional wall strength; sheetrock alone would never hold a microwave oven and it's contents.

If there is no wall behind the stove, are there brackets to attach to the cabinets to install an over-the-range microwave? None that I have seen. Nor is the microwave capable of being hung there - it is designed for most of the weight to be on the wall. Most cabinets would not hold it anyway. Sign in or sign up and post using a HubPages Network account. Comments are not for promoting your articles or other sites.

You have two problems here. But beyond that, you will have to enlarge the screw holes in the cabinet above. If there are blocks used to support the microwave, they can be moved and the existing holes re-used, but it will require a larger hole in the cabinet itself.

If there are no blocks used to distribute the weight in the cabinet you will have to supply some. Was supposed to have a 3 inch cabinet filler on both sides. Can the microwave be slid over a little to accommodate this or will it have to be removed and reinstalled. And what about the toggle bolts.

It must fasten behind and above, and to material strong enough to hold it up. One must be able to get inside any "bulkhead" above and provide strong supports, although the wall behind needs only something along the lines of sheetrock. Given those requirements can be met, though, it shouldn't be too difficult - at worst open up the structure above or construct something, and then cover the opening after adding structural support.

Any ideas on how to install oven top microwave if there isn't a cabinet but bulkhead instead? I have seen any that shallow. Amazon lists several at or just over 15" deep, but that's about it. I suspect it will be very hard to find or impossible because that will sit it quite a ways back from the front of the range and make it difficult to load and empty. Coincidentally, I very recently did just that. The last microwave I installed lasted just one year and 5 days. Five days past the warranty period. A new one was purchased, of a different brand, and installed.

The brackets were radically different - there was no chance that the old bracket would fit the new microwave. Even if I had purchased the same manufacturer, I doubt that the bracket would have fit. The same model - maybe, but even that is in doubt. Plan on removing and replacing that old bracket. If you don't have to, well and good, but you should be prepared to do so.

Thanks for the vote of confidence; I try to give instructions for someone that has never done the task before. Other product and company names shown may be trademarks of their respective owners. HubPages and Hubbers authors may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others. To provide a better website experience, dengarden. Please choose which areas of our service you consent to our doing so. For more information on managing or withdrawing consents and how we handle data, visit our Privacy Policy at: Installing an Over the Range Microwave Most of the time, installing an over the range microwave oven is not difficult, but each house is different, and problems can be encountered.

Click thumbnail to view full-size. Incomplete or Missing Electrical Connections The task began with the removal of the old range fan unit, mounted in the place the over the range microwave oven was to occupy. Installing the microwave supports Click thumbnail to view full-size. Installing the Microwave The first step in installing the new microwave is to attach the mounting bracket to the wall.

Adjusting the blower motor Click thumbnail to view full-size. Adjusting the blower As it came from the factory, the exhaust blower in the microwave was installed to recirculate air back into the room. Installing the Microwave The actual installation of the microwave is quite simple - the bottom rear of the microwave is set onto the small hooks on the rear bracket screwed to the wall, the plug and cord fed up inside the cabinet, and the unit tipped up into place. Installing an over the range microwave.

Questions must be on-topic, written with proper grammar usage, and understandable to a wide audience.